HOME  »  Andre's 1968 Triumph GT6 MK1 - 2009 Photo Gallery » 04 Jan 2009 Coil Install  (17 Slides)     [Page 1 of 1] :: Jump To  
  Up one level  
DSCN4267 * Its cold in here, not sure how bad it was, but the heaters did their work. * Its cold in here, not sure how bad it was, but the heaters did their work. * 2288 x 1712 * (1.42MB)
DSCN4268 * Right the breather. After the cap I had made broke off, I just filled the hole in with more JB Weld and put the fitting in. * Right the breather. After the cap I had made broke off, I just filled the hole in with more JB Weld and put the fitting in. * 2288 x 1712 * (1.29MB)
DSCN4269 * Gunk on the thread. Grrr. * Gunk on the thread. Grrr. * 2288 x 1712 * (1.36MB)
DSCN4270 * Did not get the focus right, but I used some Q-Tips stems shoved into the fitting and them packed the JB Weld into the cap. * Did not get the focus right, but I used some Q-Tips stems shoved into the fitting and them packed the JB Weld into the cap. * 2288 x 1712 * (1.27MB)
DSCN4271 * New coil location. * New coil location. * 2288 x 1712 * (1.29MB)
  DSCN4267  
  DSCN4268  
  DSCN4269  
  DSCN4270  
  DSCN4271  
DSCN4272 * Drilled out the holes, this was a slow careful process. * Drilled out the holes, this was a slow careful process. * 2288 x 1712 * (1.43MB)
DSCN4273 * I decided to put the bolts in this way. Easier to work with the coil. * I decided to put the bolts in this way. Easier to work with the coil. * 2288 x 1712 * (1.37MB)
DSCN4274 * 2 nuts on the left side and 3 on the right. * 2 nuts on the left side and 3 on the right. * 2288 x 1712 * (1.45MB)
DSCN4275 * I took my drill to the holes on the coil. Cleaned them up so I could slide the coil on and off easier. The plates on the bottom were catching the thread and it took some work to get the coil off after the first test fit. * I took my drill to the holes on the coil. Cleaned them up so I could slide the coil on and off easier. The plates on the bottom were catching the thread and it took some work to get the coil off after the first test fit. * 2288 x 1712 * (1.34MB)
DSCN4276 * Right now the coil in on the bulk head. I might raise it if I notice any issues. * Right now the coil in on the bulk head. I might raise it if I notice any issues. * 2288 x 1712 * (1.29MB)
  DSCN4272  
  DSCN4273  
  DSCN4274  
  DSCN4275  
  DSCN4276  
DSCN4277 * Spark plug wires in place. 1-6, 3-4, 2-5. * Spark plug wires in place. 1-6, 3-4, 2-5. * 2288 x 1712 * (1.37MB)
DSCN4278 * #4 was really the only tight one, but it will be fine. * #4 was really the only tight one, but it will be fine. * 2288 x 1712 * (1.34MB)
DSCN4279 * The old dizzy really is what's in the way. * The old dizzy really is what's in the way. * 2288 x 1712 * (1.39MB)
DSCN4280 * Cleaned up the treads. * Cleaned up the treads. * 2288 x 1712 * (1.17MB)
DSCN4281 * I will paint the cap black and cut the throttle bracket next time I have the gas pedal linkage off. * I will paint the cap black and cut the throttle bracket next time I have the gas pedal linkage off. * 2288 x 1712 * (1.33MB)
  DSCN4277  
  DSCN4278  
  DSCN4279  
  DSCN4280  
  DSCN4281  
DSCN4282 * Cut the sensor bracket, the back end was too close to the water pipe. I will also have to tape the groud wire up. A little too loose and close to the fan. * Cut the sensor bracket, the back end was too close to the water pipe. I will also have to tape the groud wire up. A little too loose and close to the fan. * 2288 x 1712 * (1.31MB)
DSCN4283 * Suggested wire route for the sensor cable. I would tie it to the MAP hose. * Suggested wire route for the sensor cable. I would tie it to the MAP hose. * 2288 x 1712 * (1.33MB)
  DSCN4282  
  DSCN4283  
Album last updated on Oct 25, 2009 - 06:03 PM
Powered by Jalbum 8.5 and BluPlusPlus skin
GT6.ca